Shure ADTQ Axient Digital PSM Quad Transmitter
The ADTQ is a four-radio digital stereo transmitter for Shure's Axient Digital PSM in-ear monitor system. Its five transmission modes are Multichannel Wideband, which uses Shure's WMAS technology to carry up to four stereo channels per radio; Narrowband for more RF power and range; SC Narrowband; Analog FM for very low latency; and Axient Digital Standard, which sends to any Axient Digital microphone receiver. Patented Spatial Diversity transmission defends against multipath.
ShowLink gives remote control of every ADXR bodypack setting from the monitor position, and the RF is encrypted. A 6.6-inch colour display, channel quality meters, Wireless Workbench networking and optional internal antenna combining come standard. WMAS features depend on regional rules. Choose the US AC model or the DC version, then the frequency band.
- System - RF Tuning Step Size25 kHz (typical)
- Dimensions44 mm × 482 mm × 385 mm (1.7" × 19.0" × 15.2") H × W × D
- Storage Temperature Range-29°C (-20°F) to 74°C (165°F)
- System - Latency (Analog Input)Analog FM: 1.29 ms; Digital: ≤2.8 ms
- DC Input (ADTQDC only)12-48 V DC, 10.1 A max
| System - RF Carrier Frequency Range | 470 to 1260 MHz, varies by region (see frequency tables) |
|---|---|
| System - Working Range | 100 m (330 ft) |
| System - RF Tuning Step Size | 25 kHz (typical) |
| System - Sensitivity | Analog FM: -94 dBm (typical) at 27 dB SINAD; Digital: -93 dBm (typical) at 10e-5 BER |
| System - Latency (Analog Input) | Analog FM: 1.29 ms; Digital: ≤2.8 ms |
| System - Audio Frequency Response | 20 Hz - 15 kHz (±1 dB) |
| System - Signal-to-Noise Ratio | Digital: 110 dB (typical) |
| System - Total Harmonic Distortion | Analog FM: < 0.5% (typical), Ref. at ±34 kHz deviation @1 kHz; Digital: < 0.01% (typical), Ref. at ±18 dBv, 1 kHz, digital gain @ 0 dB |
| System - MPX Pilot Tone (Analog FM) | 19 kHz |
| System - System Audio Polarity | Not inverted |
| Dimensions | 44 mm × 482 mm × 385 mm (1.7" × 19.0" × 15.2") H × W × D |
| Weight (ADTQ) | 4.7 kg (10.4 lb) |
| Weight (ADTQDC) | 5.0 kg (11.1 lb) |
| Housing | Steel; Extruded aluminum |
| AC Power Requirements | AC Input: 100 to 240 V AC, 50-60 Hz, 1.2 A max (6.2 A max outlet loaded); AC Output: 100-240 V AC, 5A max, 50/60 Hz UNSW |
| DC Input (ADTQDC only) | 12-48 V DC, 10.1 A max |
| RF Connector Type | BNC |
| RF Output Impedance | 50 Ω |
| Network Interface | 10/100 Mbps, 1Gbps, Dante Digital Audio |
| Fuse | T5A |
| Operating Temperature Range | -18°C (0°F) to 50°C (122°F) |
| Storage Temperature Range | -29°C (-20°F) to 74°C (165°F) |
| Audio Input - Polarity | Positive |
| Audio Input - Nominal Input Level | Switchable +4 dB u, -10 dBV |
| Audio Input - Maximum Input Level | +4 dBV: 28 dBV; -10 dBV: 16 dBV |
| Audio Input - Connector Types and Pin Assignments | Analog : 1 = ground, 2 = hot, 3 = cold; 6.35mm (¼") TRS: Tip = hot, Ring = cold, Sleeve = ground; AES3 XLR: 1 = ground, 2 = hot, 3 = cold dig audio |
| Audio Input - Impedance | 32.59 K Ω |
| Audio Input - Gain Adjustment Range | Analog: 12 dB analog (auxiliary mode); Digital: -16 to +20 dB |
| Audio Input - Protection | Analog: 50 V DC; AES3: 100 V DC |
| Audio Input - AES3 | 48, 96 and 192 KHz sample rates |
| Audio Input - Dante Digital Audio | Min. Latency: 250 µs; Supported Sample Rates: 48K, 96K; Bit Depth: 24bit |
| Headphone Output - Connector Type | Locking 3.5mm (⅛") TRS |
| Headphone Output - Minimum Load Impedance | 2 Ω |
| Headphone Output - Output Impedance | <1 Ω |
| Headphone Output - Audio Output Power | 100 mW @ 32 Ω |
| Headphone Output - L/R Stereo Separation | 300 Ω: >75 dB; 600 Ω: >90 dB; 1 kΩ: >100 dB |
| Headphone Output - Dynamic Range | 110 dB, A-weighted |
| Frequency Band (G57) | 470 to 608 MHz |
| Frequency Band (K54) | 606 to 663 MHz (with a gap between 608 to 614 MHz and a gap between 616 to 653 MHz) |
| Frequency Band (X55) | 941 to 960 MHz |









