Skip to content
G&G Technologies 201-791-1400 Search Cart

IPTV Encoder or RF Modulator: Getting a Source Onto a Building's TVs

There are two ways to put one video source on every TV in a building. An RF modulator encodes the source and puts it on a TV channel on the coax, so any TV that tunes digital cable or broadcast channels can watch it. An IPTV encoder sends the source over the network as an MPEG transport stream, and set-top boxes, smart TVs or players on that network pick it up. The cabling already in the walls usually decides which one you buy.

The 7 Picks

RF modulator (coax)
IPTV encoder (network)
Both
Input
HDMI, embedded or analog audio
One DIN: component or VGA, analog or digital audio
Two DIN: component or VGA, analog or digital audio
6 composite video with analog audio
HDMI and 3G-SDI with loop-through, USB
SDI with loop-through
Component, composite, HDMI, SDI
Max input
1080i/1080p
1080p
1080p
SD
HDMI 3840x2160 30fps, SDI 1080p60
2048x1080 60fps
Full HD
Codec
MPEG-2 HD
MPEG-2 HD
MPEG-2 HD
MPEG-2
H.265, H.264
H.264 or HEVC
MPEG-2 and H.264
RF output
QAM 256 and 64 (J.83 Annex B), CATV channels 2-135
QAM 256 and 64 (J.83 Annex B), CATV channels 2-135
QAM 256 and 64 (J.83 Annex B), CATV channels 2-135, +45 dBmV typical
6 channels on 2 QAM frequencies, or on 3 DVB-T/C frequencies
Not listed
Not listed
ATSC
Network
Ethernet for control only
Ethernet for setup through a web page
Ethernet for setup and firmware
RF only
Not listed
Not listed
Not listed
Power
100–240 VAC 50/60 Hz, 60W max. 30W Typical IEC 60320–C14
100–240 VAC 50/60 Hz, 60W max. 30W Typical IEC 60320–C14
100–240 VAC 50/60 Hz, 60W max. 30W Typical IEC 60320–C14
Not listed
12V DC or PoE
DC 5V/3A; Max power consumption
Not listed
Notable
Not listed
Not listed
Not listed
Latency: Programmable, 200 - 400 ms
Network output: TS over UDP, RTSP, SRT, RTMP/RTMPS, HLS, NDI HX2/HX3, up to 8 at once
Network output: TS over UDP and RTP, RTSP, RTMP, RTMPS, SRT, NDI HX2, HLS
Network output: TS over IP (UDP), plus ASI; Latency: 150 ms
Use it for
An HDMI source such as a cable box or media player, sent to every TV on the coax as one cable channel, which each TV's own tuner picks up.
One component or VGA source on the building coax, for older gear with no HDMI output.
Two component or VGA sources in one box on the building coax, so two sources need one unit and not two.
Six SD sources, such as security cameras or older players, in an HDb3000 headend chassis, with six inputs on one blade where single-channel units would take six.
A 4K HDMI or an SDI source sent to players and smart TVs on the network, while also streaming out to a platform, since it sends up to 8 outputs at once.
An SDI camera or switcher feeding a network TV system as a transport stream, taking the SDI signal directly.
One source sent to TVs on the coax as an ATSC channel and to the network as TS over IP at the same time, so coax TVs and network TVs both get the source from one box.
Price
$1,760.00
$1,022.40
$1,268.80
$1,330.00
$499.00
$555.00
Discontinued
RF modulator (coax)
Kramer ZvPro810-NA HD video encoder/QAM modulator with 1 HDMI video input up to 1080i/1080p with embedded digital audio or
Kramer ZvPro810-NA HD video encoder/QAM modulator with 1 HDMI video input up to 1080i/1080p with embedded digital audio or
Specs
Input
HDMI, embedded or analog audio
Max input
1080i/1080p
Codec
MPEG-2 HD
RF output
QAM 256 and 64 (J.83 Annex B), CATV channels 2-135
Network
Ethernet for control only
Power
100–240 VAC 50/60 Hz, 60W max. 30W Typical IEC 60320–C14
Use it for
An HDMI source such as a cable box or media player, sent to every TV on the coax as one cable channel, which each TV's own tuner picks up.
$1,760.00
Kramer ZvPro610-NA HD video encoder/QAM modulator with one DIN input for Component video/digital and analog audio or VGA
Kramer ZvPro610-NA HD video encoder/QAM modulator with one DIN input for Component video/digital and analog audio or VGA
Specs
Input
One DIN: component or VGA, analog or digital audio
Max input
1080p
Codec
MPEG-2 HD
RF output
QAM 256 and 64 (J.83 Annex B), CATV channels 2-135
Network
Ethernet for setup through a web page
Power
100–240 VAC 50/60 Hz, 60W max. 30W Typical IEC 60320–C14
Use it for
One component or VGA source on the building coax, for older gear with no HDMI output.
$1,022.40
Kramer ZvPro620-NA HD video encoder/QAM modulator with two DIN inputs for Component video/digital and analog audio or VGA
Kramer ZvPro620-NA HD video encoder/QAM modulator with two DIN inputs for Component video/digital and analog audio or VGA
Specs
Input
Two DIN: component or VGA, analog or digital audio
Max input
1080p
Codec
MPEG-2 HD
RF output
QAM 256 and 64 (J.83 Annex B), CATV channels 2-135, +45 dBmV typical
Network
Ethernet for setup and firmware
Power
100–240 VAC 50/60 Hz, 60W max. 30W Typical IEC 60320–C14
Use it for
Two component or VGA sources in one box on the building coax, so two sources need one unit and not two.
$1,268.80
ZeeVee HDb3000 Composite Media Module Blade
ZeeVee HDb3000 Composite Media Module Blade
Specs
Input
6 composite video with analog audio
Max input
SD
Codec
MPEG-2
RF output
6 channels on 2 QAM frequencies, or on 3 DVB-T/C frequencies
Network
RF only
Notable
Latency: Programmable, 200 - 400 ms
Use it for
Six SD sources, such as security cameras or older players, in an HDb3000 headend chassis, with six inputs on one blade where single-channel units would take six.
$1,330.00
IPTV encoder (network)
Kiloview E3 4K Multi-Interface Video Encoder
Kiloview E3 4K Multi-Interface Video Encoder
Specs
Input
HDMI and 3G-SDI with loop-through, USB
Max input
HDMI 3840x2160 30fps, SDI 1080p60
Codec
H.265, H.264
Power
12V DC or PoE
Notable
Network output: TS over UDP, RTSP, SRT, RTMP/RTMPS, HLS, NDI HX2/HX3, up to 8 at once
Use it for
A 4K HDMI or an SDI source sent to players and smart TVs on the network, while also streaming out to a platform, since it sends up to 8 outputs at once.
$499.00
Magewell Ultra Encode SDI Streaming Encoder (53120)
Magewell Ultra Encode SDI Streaming Encoder (53120)
Specs
Input
SDI with loop-through
Max input
2048x1080 60fps
Codec
H.264 or HEVC
Power
DC 5V/3A; Max power consumption
Notable
Network output: TS over UDP and RTP, RTSP, RTMP, RTMPS, SRT, NDI HX2, HLS
Use it for
An SDI camera or switcher feeding a network TV system as a transport stream, taking the SDI signal directly.
$555.00
Both
Ez-Caster EN3 HD Encoder and ATSC Modulator
Ez-Caster EN3 HD Encoder and ATSC Modulator
Specs
Input
Component, composite, HDMI, SDI
Max input
Full HD
Codec
MPEG-2 and H.264
RF output
ATSC
Notable
Network output: TS over IP (UDP), plus ASI; Latency: 150 ms
Use it for
One source sent to TVs on the coax as an ATSC channel and to the network as TS over IP at the same time, so coax TVs and network TVs both get the source from one box.
Discontinued

What Matters

Use a modulator. The ZeeVee ZvPro units put an MPEG-2 channel on QAM 256 or 64, frequency agile across CATV channels 2-135, so the TVs tune it like any cable channel, with no set-top box or network connection at the TV. The ZvPro810 takes HDMI up to 1080p. The ZvPro610 and ZvPro620 take component or VGA through one or two DIN inputs.

Use an IPTV encoder that sends TS over UDP. The Kiloview E3 takes HDMI up to 4K30 or 3G-SDI and sends up to 8 streams at once, including TS over UDP, SRT and NDI. Over the network the stream reaches any device on it, with no coax needed. The Magewell Ultra Encode SDI sends TS over UDP and RTP from an SDI camera or switcher.

The Lumantek ez-Caster EN3 encodes MPEG-2 or H.264 from component, composite, HDMI or SDI and outputs an ATSC RF channel, ASI and TS over IP from the same box, at 150 ms latency. It is the top tier here. One box covers both kinds of TV without a second encoder.

A headend chassis scales further than single boxes. The ZeeVee HDb3000 Composite blade puts six SD composite sources on two QAM frequencies. It installs in the HDb3000 chassis and needs CAVC6 breakout cables, sold separately. One chassis holds several blades, so channel count grows without adding separate boxes.

None of the modulators here go past 1080p. For a 4K source the network route is the one that keeps it: the Kiloview E3 encodes HDMI up to 3840x2160 at 30 fps in H.265.

The IPTV encoders sit in the entry tier. The single-channel ZvPro modulators are the middle tier, and the EN3, which does both jobs, is the highest.

Questions

A box that takes a video source and sends it across a local network as a transport stream, usually TS over UDP, for set-top boxes, smart TVs or players to receive, so any device on the network that can decode the stream can show it. The Kiloview E3 and the Magewell Ultra Encode SDI both output TS over UDP.

When the TVs are fed by coax rather than the network. A modulator such as the ZeeVee ZvPro810 puts the source on a QAM cable channel, so each TV tunes it with its own tuner. If you need both, the Lumantek ez-Caster EN3 outputs an ATSC RF channel and TS over IP together.

None of the modulators here encode past 1080p. To carry a 4K source, send it over the network: the Kiloview E3 encodes HDMI up to 3840x2160 at 30 fps.

Questions? Talk to a Person.

Call (201) 791-1400 or email [email protected] - we've handled pro audio & video since 1988.