|
Specifications: |
MICROPHONE INPUT
- Connector: Female XLR Pin 2 Hot
- Type: Electronically balanced/unbalanced
- Impedance: 330O
- Max Input Level: -9 dBu or +11 dBu with 20 dB pad engaged
- CMRR: >40dB, Typically 55dB
- Equivalent Input Noise: Typically -120 dBu with a 150O source load, 20Hz to 20kHz BW
LINE INPUT (REAR PANEL)
- Connectors: TRS 1/4" Jack
- Type: Electronically balanced/unbalanced
- Impedance: 20kO unbalanced, 40kO balanced
- Maximum Input Level: +21dBu balanced or unbalanced
- CMRR: >40dB, Typically 55dB
- Gain (Drive Control): -15dB to +15dB
INSTRUMENT INPUT (FRONT PANEL)
- Connector: TS 1/4" Jack
- Type: Unbalanced
- Impedance: 470kO
- Maximum Output Level: >+21 dBu unbalanced
ANALOG OUTPUTS
- Connector: Male XLR Pin 2 Hot and TRS 1/4"
- Type: Servo-balanced/unbalanced
- Impedance: Balanced 120O, unbalanced 60O
- Maximum Output Level: >+21 dBu, >+20 dBm (into a 600O load)
INSERT
- Connector: TRS 1/4"
- Type: Unbalanced
- Impedance: 100O (SEND), 20kO (RETURN)
DIGITAL OUTPUTS
- Connector:
XLR for AES/EBU
RCA for S/PDIF
- Impedance:
110O for AES/EBU
75O for S/PDIF
WORD SYNC INPUT/OUTPUT
- Connectors: BNC
- Input Impedance: 75O terminated by internal jumper
- Input: 96, 88.2, 48, or 44.1kHz word clock
- Output: 96, 88.2, 48, or 44.1kHz word clock
SYSTEM PERFORMANCE
- DRIVE Control Range:
+30dB to +60dB for Mic Input
-15dB to +15dB for Line and Instrument Inputs
- Output Level Control Range: -20dB to +20dB
- LINE: Selects between microphone and line inputs
- Phantom Power: +48V
- PAD: 20dB pad
- PHASE: Reverses pins 2 and 3 of the microphone input XLR
- LOW CUT: 75Hz, 12dB/octave high pass filter
- Analog Frequency Response: <10Hz to 75kHz
- THD + Noise: 0.35% typical at +4dBu out, 1kHz, 40 dB gain
EQUALIZER
- LOW Frequency: 80 Hz, shelving filter
- HIGH Frequency: 12 kHz, shelving filter
- MID Frequency:
Sweepable from 100 Hz to 8 kHz, bandwidth 1.5 octaves
Gain (all bands)
Sweepable from –15 to +15 dB
COMPRESSOR
- Threshold Range: -40 dBu to +20 dBu
- Threshold Characteristic: Selectable OverEasy® or Hard Knee
- Compression Ratio: Variable; 1:1 to Infinity:1; 60 dB maximum Compression
- Attack Time: Program-dependent; Typically 5 ms (SLOW disabled), 15 ms (SLOW enabled) for 15 dB Gain Reduction
- Release Time: Program-dependent; Typically 50 dB/sec (SLOW disabled), 8 dB/sec (SLOW enabled)
DE-ESSER
- Characteristic: Wideband gain reduction
- Frequency Range: 800 Hz to 10 kHz High Pass
- Release Time: 12 dB/octave program-dependent; approximately 1 ms/dB
ANALOG TO DIGITAL CONVERSION
- Type: dbx® Type IV® A/D Conversion System
- Sample Rate: 96, 88.2, 48, or 44.1kHz selectable
- Wordlength: 24, 20, or 16 bit selectable
- Dither Type: TPDF, SNR2, or none
- Noise Shape: Shape 1, Shape 2, or none
- Output Format: S/PDIF or AES/EBU
- Convertor Dynamic Range: 107dB typical, A-weighted, 22kHz bandwidth
POWER SUPPLY
- Operating Voltage:
DO: 120VAC 60Hz, 100VAC 50/60Hz
EU: 230VAC 50/60 Hz
- Power consumption: 35W
|
|